Hello my lovelies! We’re finally in December, and that means the countdown to Christmas has begun! Since we’re in the lead up to Christmas, everyone is decorating their homes (if they haven’t already – to tell you the truth my house has been decorated since the 1st November!) I’ve been doing some festive diy’s!
One decoration I’ve seen, not for Christmas, but for all year round, was of some cute gnome pine cones. And it got me thinking that if I added a few details I could make these myself, and make them into some very cute Santas! And I managed to make about 25 of them for about £15 in total for all of the supplies!
So, here’s what you’re going to need:
- Red and White Felt (and any other colours you want for your santa hats!)
- Pine cones
- Pom poms
- White yarn
- Wooden beads
- Hot glue gun (plus some hot glue sticks)
I found everything I needed from Ebay and Amazon (if you buy from Amazon, make sure you’re on their Amazon Smile website as they donate money to a charity of your choice each time you buy something!) and everything arrived within a few days.
Right. Let’s get into it!
Step 1: Pick out your pine cone, I chose frosted pine cones for an even more Christmassy feel, then grab some felt in the colour you want for your santa hats. Using a pencil and some yarn, decide how tall you want your hat, and then hold down the end of the yarn at the corner of the felt and draw a 1/4 of a circle.
Step 2: Cut out your 1/4 of a circle and put away any excess for making more hats later. Or you can make a bulk batch of hats in one go, the choice is yours! Now plug in your glue gun, making sure you’ve got it on a safe surface as some glue can come out of the tip as it heats up so be careful!
Step 3: Once your glue gun is hot and ready to go, put a line of glue down one of the straight edges. Next up is rolling up the felt into its cone shape! I recommend starting at the tip of the hat (the corner of the felt will be the tip) and working your way down, be careful with this part and take your time so you don’t burn yourself!
Step 4: Once you’ve got yourself a cone hat, put it on top of your pine cone and double check it’s sitting how you want it to, and if you need to, give it a trim like I did. Now that the main part of your Santa hat is ready, it’s time to add that white trim! Grab your white felt and cut a strip of it, long enough to go round the bottom of the hat, I don’t measure this part and just trim off any extra but you can definitely measure it if you want to! The strip I use is usually around 1.5-2cm thick.
Step 5: It’s time to attach the white trim to the hat, so grab your glue gun and put a line of hot glue over the white felt and carefully wrap it round the bottom of your hat. I definitely glued my fingers a few times during this part so be wary if you’ve never got hot glue on yourself before!
Step 6: Pick your desired pom pom! I went for the classic white pom pom but in the pack I got from Ebay I got a mix of the red, green and white. Use a small blob of hot glue and add it onto the end of your hat! If your hat is especially pointy, you can snip the tip off so you have more space to add the pom pom to. Now add a ring of glue on the inside of your hat (this part reminds me of the Matilda movie) and stick it onto your pine cone so it’s secure!
Step 7: Now it’s time to make Santa’s beard! Grab your white yarn and wrap it around your fingers until you’ve got a decent bundle, remember not to do it too tight, you still want to be able to move your fingers! Then chop the end of the yarn from the bundle, leaving about 15-20cm of yarn unwrapped.
Step 8: Here comes the slightly fiddly part. With the end of the yarn, thread it between your fingers a few times, so you create a bowtie shape. Then you’re going to thread the end of the yarn through on of the sides of your bowtie, leaving a loop. Here you can switch to just two fingers wrapped in the yarn.
Step 9: With your yarn now threaded through one of your bowtie sides, you want to thread the end of your yarn through the loop you’ve just made and pull it fairly tight. Now repeat the process once again and cut off any extra yarn.
Step 10: Time to make Santa’s bowtie into a beard! Take the bundle off your fingers, and cut along the looped edges (a bit like what you do when you make pom poms) on either side, and you’ll have a funny looking bow.
Step 11: Using your hands you can shape the bow into a beard shape. Once you’ve got it to a shape you’re happy with, add a bit of hot glue to the back, where you wrapped the yarn to bind it together, and stick it onto your pine cone. You may need to hold it in place for a few seconds to make sure it sits how you want it to!
Step 12: The final step! Add a small blob of hot glue to the very top and centre of Santa’s beard and add on your wooden bead as his nose!
And voila! You’re done and your Santa is ready to be put on your tree, used as table decorations, given as gifts or pur all around your house! I personally find these super cute, and you can change up the style of them so they suit your taste, I’ve made a few with hats that are flopped down, and a few in green since Santa was originally in green instead of red! I’m also thinking of making a few in some more colours to match the different coloured tree decorations we’ve got going on this year! I find these quite mindful and relaxing to make, so when I’m making them I put on a movie with some snacks and a cup of tea, and before I know it I’m surrounded by Santa gnomes!
What crafts and Christmas diy’s are you doing this year? Let me know if there’s any you’d like to see me try, and if you try these, let me know how it goes and tag me on insta @theweightofmyworlds so I can see your cute crafts!
Have a great weekend my loves and Happy Holidays!